Sign In | Join Free | My vivirlatino.com
vivirlatino.com
Wuxi Zuudee Special Alloy Co.,Limited.
To be honest to alloy is honest to life.
Home > Nimonic >

Nimonic 101 and X8CrNiMoNb16-16/1.4981 flat bar from a Germany customer

Wuxi Zuudee Special Alloy Co.,Limited.

Nimonic 101 and X8CrNiMoNb16-16/1.4981 flat bar from a Germany customer

Place of Origin : Wuxi
Brand Name : Zuudee
Certification : 3.1A,Tuv,SGS,ISO9001,etc.
Model Number : SuperAlloy.org
MOQ : upon discussion
Packaging Details : wooden packaging
Delivery Time : normally 25-45 days
Payment Terms : T/T
Supply Ability : 3000MT/month
Contact Now

Nimonic 101 and X8CrNiMoNb16-16/1.4981 flat bar from a Germany customer

Nimonic 101
flat bar 70 x 70 mm 44 pieces each 235 mm
flat bar 70 x 70 mm 44 pieces each 255 mm
flat bar 70 x 70 mm 44 pieces each 285 mm
flat bar 70 x 70 mm 44 pieces each 300 mm

Solution annealing: 1100℃/2 h/ Furnace cooling
To 650℃ then air cooling
Hardnesses: 650℃/24 h/ heat up 760℃/8 h/ air cooling
Copy of the furnace diagram

To the achievement of an optimal grain size (=ASTM-E or more finely, isolates 112, No. 1 to size 0; The transition to different grain size must run gradually; at the grain boundaries of larger grains no chains of smaller grains may arise; no duplex structure permitted) has to take place an adjustment from forging procedure and thermal treatment to.

Surface roughness: Rz 14 and Rmax – 20 amounted (DIN 4768, sheet 1)

Microscopic examination for the determination of the degree of purity
SEP-1570.
Evaluation procedure: K
Sum characteristic value – (K1<28)

DIN 50145, short proportional staff according to DIN 50125, with Lo = 5 x do.
Sample situation: radially. Constriction is to be determined and indicated informatively.
Yield strength: Rp0,2 = min. 650 MPa
Tensile strength: Rm = 100 – 1300 MPa
Elongation: A5 = min. 12 %
Energy of impact = min. 25 J longitudinal
DIN 50351, HB 30/10
100 % hardness test

Short time condition attempt Inspection temperature: 815℃ Test load: 300 MPa The samples must get over a load period of 25 h without break. The attempt is to be continued up to the sample break. The break msus in the smooth sample part take place.
Aking to AMS 5660

Radially at the transition sheet foot. Preservation time of the inspection temperature before the load on the sample is brought: 60 min.

After the prescribed 25-h can the load in intervals of 8 – 16 h around in each case 35 MPa be raised. The test sequence (number and height of load increases) is to be indicated in the certificate of acceptance test.

Short time creep test Inspection temperature: 750℃
Test load: 180 MPa
Load period: 100 h
A5 may not amount to 0.2%.
DIN 50125, short proportional staff

surface crack test

As rolled as possible. Quantity tolerance: The given up quantity is a minimum supply, it can up to 5% over quantity be delivered. Longitudinal dimension of the staffs: The length of the staffs is to be co-ordinated after the necessary pieces. For each thermal treatment lot is to be planned sufficient material for a sampling.

At rolled staffs:
diameter: flat 70 x 70 mm
tolerance: according to DIN 1017

At forged staffs:
diameter: flat 69 x 69 mm
tolerance: according to DIN 7527 Cross-sectional shape E

Forging ends with 50 mm air passage In accordance with Q-St-D-51-225 US examination is to be accomplished at the finished forging (flat bar). All pieces are to mark by: Auftr. – NR., stock of material NR., material, samples/load NR., manufacturer characters For all examinations a certificate of acceptance test is to be provided after EN 10204/3.1 German + English.

Note: The fiber direction must run in longitudinal direction (235 mm, 255 mm, 285 mm, 300 mm). This is valid both for rolled and for forged execution of the staffs. Reason: From the flat bars highly loaded turbine rotor blades are manufactured, whose main load direction in the longitudinal axis runs.

X8CrNiMoNb16-16/1.4981
Flat bar 23 x 52 mm 60 pieces each 205 mm
Flat bar 27 x 63 mm 50 pieces each 120 mm
Flat bar 27 x 63 mm 54 pieces each 130 mm
Flat bar 27 x 63 mm 56 pieces each 120 mm
Flat bar 96 x 52 mm 62 pieces each 135 mm
Flat bar 96 x 52 mm 52 pieces each 155 mm
Flat bar 96 x 52 mm 56 pieces each 155 mm
Flat bar 96 x 52 mm 58 pieces each 155 mm

Quantity tolerance: The given up quantity is a minimum supply, it can to 5% over quantity be delivered. Longitudinal dimensions of the staffs: The length of the staffs is to be co-ordinated after the necessary pieces. For each thermal treatment lot is to be planned sufficient material for a sampling.

At rolled staffs:
diameter: flat 23 x 52 mm
tolerance: according to DIN 1017

according to Q-St-E-51-210
Point 5,4 is void All pieces are to mark by: Auftr. – NR., stock of material NR., material, samples/load NR., manufacturer characters For all examinations a certificate of acceptance test is to be provided after EN 10204/3.1 into German + English.

Note: The fiber direction must run in longitudinal direction. Reason: From the flat steel bars highly loaded turbine rotor blades are manufactured, whose Hauptbelasungsrichtung in the longitudinal axis runs.

X3CrNiMo134/1.4313
Flat bar 30 (+-1) x 95 (+-1) 1 pieces each 500 mm

According to TLV 1205

X12CrNiMo12/1.4939
Flat bar 170 x 253 mm 1 pieces each 840 mm

According to Q-St-D-51-231:
ESU-Quality
Ferritpart may not exceed 2%
K0<20
EN 10002, short proportional staff with Lo = 5
Yield strength: Rp0,2 = min. 785 MPa
Tensile strength: Rm = 900 – 1100 MPa
Elongation: A5 (lengthwise) = min. 14 %
Contraction: Z = informative
EN 10045, ISO-V-test
1 set = 3 tests
Av (lengthwise) = min. 40 J
Ultrasonictest: Class 1a
100 % volumetest according to No D2 with 4 MHz according to SEP 1923
Number of tests:
Test 5.3: 2 tests from the hardest or softest bar from each heat and heat treating batch
Test 5.4: (1 set = 3 tests)
2 tests from each heat from the hardest and softest bar from each heat and heat treating batch
Lengthwise accordingly EN 10088

Quantity tolerance: The given up quantity is a minimum supply, it can up to 5% over quantity be delivered. Longitudinal dimensions of the staffs: The length of the staffs is to be co-ordinated after the pieces needed by us.

At rolled staffs:
diameter: flat 196 x 253 mm
tolerance Ma?”B”: +- 2,5 mm
tolerance Ma?”S”: +- 2,0 mm

At forged staffs:
diameter: flat 193 x 250 mm
tolerance: according to DIN 7527 Cross-sectional shape E

Forging ends with 50 mm air passage


If you have any inquiries about nickel alloys,please feel free to check with us via info @zuudee.com,thanks.
Wenn Sie Fragen zu Nickellegierungen haben, zögern Sie nicht, mit uns über info @ zuudee.com ,dank.
Si vous avez des questions sur les alliages de nickel, se il vous plaît sentir libre pour vérifier avec nous via info @ zuudee.com, merci.
Si usted tiene alguna pregunta acerca de las aleaciones de níquel, no dude en consultar con nosotros a través de info @ zuudee.com, gracias.

China Customized Inflatable Bumper Ball Game Bubble Adult Grass CE supplier

Nimonic 101 and X8CrNiMoNb16-16/1.4981 flat bar from a Germany customer Images

Inquiry Cart 0
Send your message to this supplier
 
From:
Enter your email please.
To: Wuxi Zuudee Special Alloy Co.,Limited.
Subject:
Message:
Characters Remaining: (0/3000)
 
Inquiry Cart 0